17 results for '86-310'

News & Information (17)

Dirty Money Clip Tutorial(Post)

Created by: Rita HutchinsonDesigner TipsClean both parts with alcohol and allow to dry. Apply flux to key points on the back of the scarab, and then apply small dots of solder to these points using s ...

Gypsy Dancer - Earrings Tutorial(Post)

Created by: Mollie ValenteDesigner TipsColorize the raw brass filigrees. (See Rings & Things blog post "Jewelry DIY - Colorizing Raw Brass Filigrees" for instructions.)Make a bead dangle and atta ...

Hearts Across the States Keychain Tutorial(Post)

Created by: Janet BoyingtonDesigner TipsStamp hearts in desired locations on USA blank, and then use the "." (period) from the punctuation set to connect the hearts. (New to metal stamping? See Metal ...

Red Bird Enameled Earrings Tutorial(Post)

Created by: Rita HutchinsonDesigner TipsPosition and emboss pattern on blanks with the Big Shot Jewelry Studio and embossing die. (See Big Shot Embossing blog article)Counter-enamel the blank (fire t ...

Aztec Princess Earring Tutorial(Post)

This project uses Swarovski crystals. Created by: Tiffany WhiteDesigner TipsMark all six of your triangle blanks with a permanent marker dot in one of the points and straight down on the opposite sid ...

Eclipse Cuff Links Tutorial(Post)

Created by: Mollie ValenteDesigner TipsClip the loop off both moon charms, file smooth, and sand with a 600 grit polishing cloth.Use a dapping block to gently dome the moon charms.Soft solder each mo ...

A Dog's Night Out Collar Tutorial(Post)

Created by: Valorie Nygaard-PouzarDesigner TipsWhether it be the park or the opera, your pooch will prance in style with this custom and personalized doggie necklace.Determine the total length of the ...

Funky Bohemian Spike Set Tutorial(Post)

Created by: Tiffany WhiteDesigner TipsCut three pieces of 20-gauge copper wire, each 6" long.Make a wrapped loop at one end of each wire.For step-by-step illustrated instructions, see our blog articl ...

Puppy Love Pin Tutorial(Post)

Created by: Mollie ValenteDesigner TipsThe Complete Metalsmith (#62-011) provides a useful chart for selecting saw blades. Or scroll down to the comments section of our "Tips for Sawing Sheet Metal w ...

Mehandi Coil Bracelet Tutorial(Post)

Created by: Rita HutchinsonDesigner TipsUse shears to cut flat wire. Texture as desired with texturing hammer or metal stamps.Create coil by wrapping at an angle around large barrel of bail making pl ...

Cowgirl Cuff Bracelet Tutorial(Post)

Created by: Tiffany WhiteDesigner TipsUse the pein side (rounded) of your hammer to texturize the surface of the copper metal strip on the steel block.Using your metal shears, cut a 3/4 inch by 4 inc ...

Cave Man Necklace Tutorial(Post)

Created by: Jaci BostonDesigner TipsCarefully plan the cutting pattern. The shape of these cuts creates decorative prongs or tabs to hold the gemstone slab bead.For this design draw the shape to be c ...

Tri-Tone Cuff Bracelet Tutorial(Post)

Created by: Rita Hutchinson   Designer TipsUsing a pre-cut and finished bracelet blank, and precut 6" patterned wire makes this bracelet assemble in a snap!Apply pattern to copper blank with des ...

Astral Love Resin Necklace Tutorial(Post)

Created by: Rita HutchinsonDesigner TipsSee instruction page for making no-solder bezels.Cut paper to match bezel wire shape.Seal paper and adhere to inside of bezel.Mix a small batch of resin and po ...

Bee Keeper Reliquary Necklace Tutorial(Post)

Created by: Mollie ValenteDesigner TipsFor a step-by-step tutorial with images, check out the How to Create a Reliquary Pendant blog post.Cut and shape the blank: Measure and cut a brass blank 1 x 1- ...

Aurora Sprinkles Earrings Tutorial(Post)

Created by: Rita Hutchinson   Designer TipsCut bezel strip to size (one 8-12" piece) and flatten/ work harden with nylon hammer.Add texture to both sides of bezel strip with texture stamping ham ...

Go West Necklace Tutorial(Post)

Created by: Mollie ValenteDesigner TipsMaking the Pendant:Cut the handle loop of the heart charm and file smooth.Mark hole locations with a Sharpie®, and use the hole punch to make two 1/16th-inch ha ...