Rings & Things Jewelry Blog

Created by: Mollie Valente Designer TipsOpen the chain necklace's clasp.Thread the jump-ring side of the chain necklace through the side-to-side holes in each pearl ball bead, one bead at a time.If you are not able to match up the chain with the opposite exit-side bead hole, try this: Attach a piece of thin wire to the jump-ring side of the chain necklace. Use the wire "needle" to string on the pearl ball beads.  When done, remove the piece of wire.Suggested Supplies3 each  #20-66 …

Created by: Mollie ValenteDesigner TipsTwist a jump ring to open it extra wide.Loop the jump ring around a single pearl in the pearl ball bead.Attach the loop of a French hook ear wire to the jump ring.Twist the jump ring closed.Repeat to make the second earring.Suggested Supplies2 each #20-660-011 Freshwater Pearl Bead, Ball, 10-12mm - White1 dozen (use 2 pieces)  #34-533-SUB Sterling Silver French Hook Earring Wires, Economy1 ten (use 2 pieces) #37-295-2 …

Created by: Summer Melaas Designer TipsCarefully mark spots for holes, and use smaller end of EuroTool "helicopter" punch to add holes to corners of copper blanks.Clean the blank with Penny Brite per package instructions. Rinse thoroughly and avoid touching further.Spray klyr fire onto blank, and sift on a base coat of white enamel.Mix a small amount of each enamel color that you plan to use with Klyr Fire or distilled water in separate well or container. Mix each with brush. Desi …

Created by: Megan Holden Designer TipsUse beading board or beading mat to arrange beads in pattern as shown in picture.String 10 seed beads onto a 20"" piece of beading cable and then building up on each side, add: 1 copper hogan, 6mm Dzi, spacer, 8mm Dzi, copper rondelle, 8mm Dzi, spacer, 6mm Dzi, hogan, 8 seed beads, hogan, 6mm Dzi spacer, 8mm Dzi, spacer, 6mm Dzi, hogan, 6 seed beads, hogan, 6mm Dzi, hogan and then fill to ends as needed for 16" or 18" length, with more seed beads.Finish …

Dance the night away with shining faux kabibi disks, sparkling faceted gemstone beads, and sassy, swinging chain.  Designer TipsCut five pieces of chain: three 3.5"", one 4"" and one 4.25"".On one end of a 3.5"" piece of chain, use a jump ring to attach your lobster clasp. For step-by-step wire-wrapping instructions, and most secure way way to open and close jump rings, see Jewelry Basics 101 (PDF).Cut a piece of wire (about 2""). Using round nose pliers, create a loop on one …

Created by: Mollie ValenteDesigner TipsFor instructions with step-by-step photos, please see our blog article: How to Make an Adjustable Necklace Extender.Suggested Supplies1 foot (use 4") #40-011-001-4-FT  Gold Plated Oval Cable Chain by the FOOT, 2.2mm1 ounce (use 2 pieces) #37-133-2  Yellow Plated Jump Ring, Round, Heavy, 4.5mm1 half-gross (use 1 piece) #39-240-4  Gold Plated Lobster Clasp, 6x10mm1 each #49-958-86-AG  TierraCast Antiqued …

Created by: Veronica GreenwoodDesigner TipsCut two 18" pieces of leather.Fold one strand in half. Make a larks-head knot by feeding both ends through the loop on the anchor charm, then back through the leather loop formed on the other end of the cord. Pull tight.Fold the other strand in half over the other end of your anchor and feed both ends through the loop formed. Pull tight.At one side of the bracelet, add a porcelain bead, a small barrel bead, and another porcelain bead to both strands of …

Created by: Veronica Greenwood   Designer TipsChoose the size of chaton to nestle into the center of your succulent charm. Using the GS Hypo Cement add a little glue in the center of your charm and place your chaton. Set aside to dry.Cut approximately 9" of leather.Slide one barrel bead and your button, onto the leather. Go back through your barrel bead, and using needle-nose pliers, crimp the barrel bead to create a secure loop at one end of the cord.Slide your three pearls onto the leathe …

This is a lovely summery design with secure wire-wrapped links, and can also double as  November birthstone jewelry (citrines) or June (pearls).Created by: Veronica Greenwood Designer TipsUsing a 12" piece of wire, wrap one 4mm citrine bead, one 4mm apatite, and one 4mm citrine around a section of the 26mm hammered link.Using a jump ring, attach all three hammered rings to the center link of your chain.For wire-wrapped loop instructions, and most secure way way to open and close jump r …

No fancy beading techniques or knots required -- If you can string beads with a needle and thread, you can create lovely designs with these bracelets!  Created by: Veronica Greenwood   Designer TipsStretch and wax 1 yard of Beige 1-G thread, or use .006" Fireline. Follow instructions in this video, or the PDFs below, to add Delicas in desired pattern to the bracelet.You'll have plenty of left-over beads of each color after making this project.  Suggested Supplies  1 …